Reclaimed Wood Wine Bottle Vase Trio

Salvage Wood Wine Bottle Wall Vase Trio

Wine Bottle Wall Vase2 copy

 Reclaimed wood and recycled bottles combine with inexpensive copper hardware for this rustic, ecofriendly wall vase set.  Make it in under an hour with just a few dollars for hardware!  This is perfect inexpensive wall decor, and makes a great, unique handmade gift for the holidays.

MATERIALS

Wine Bottle Wall Vase 4

-Scrap wood cut to desired width (The board I had was 25 inches, so I went with that.  Use any number of wine bottles, and cut your wood the appropriate length for that number.)

-Drill

-1 inch copper bell hanger kit (available in plumbing section of most hardware stores for less than $2 each)

-Picture hanging hardware

-Wine bottles (clean and remove labels if desired as described in Techniques)

 DIRECTIONS

 1.  Paint, stain or decoupage your wood any way you like.  I left mine as I found it since it had the weathered look I love.  Same goes for the bottles.  Paint or decorate them to fit your decor or occasion.

Measure for holes

2.  Measure and mark placement of your bottles, leaving even spacing between each and centering them on the board.  Yay math!

Drill hole for clamps

3.  Drill a pilot hole with a drill bit just smaller in diameter than your screw.  If you aren’t using a drill, use a hammer and nail to make a pilot hole.

Wine bottle wall hanging

4. Attach bell hanger using the screw that came in your kit and a drill or screwdriver.

How to make a reclaimed wood wall hanging

5.  Attach a loop for hanging on each side.

Wine Bottle Wall Vase3

6.  Place on wall and add wine bottles.  Time to head to the farmer’s market for some fresh flowers!

Recycle Wine Bottles into Inexpensive Wall Decor with Reclaimed Wood @savedbyloves

DIY Upcycle Liquor Bottle to Mercury Glass Lamp

How to make Mercury Glass

Get the look of expensive mercury glass with a can of spray paint and some Epson salt!  This simple project takes a genie lamp shaped liquor bottle to an elegant mercury glass lamp for way less than the purchase price you see in stores.

Mercury Glass Lamp Tutorial

MATERIALS

Mercury Glass Lamp 5 

-Glass Bottle of your choice

–Krylon Looking Glass Spray Paint

–Krylon Spray Adhesive Remover

-Epson Salt

-Kraft paper, plastic or other work surface protector

-Drill and 1/2 inch Diamond Hole Drill Bit

-Lint free towel and rubbing alcohol

-Dust mask

-Protective Gloves

-Protective Eyewear

-Container of water with a a soaked towel or rag

–Bottle Lamp Kit

-Lamp Shade

-Light Bulb

DIRECTIONS

 

1.  Clean bottle and remove labels; to do this, soak bottles in hot, soapy water and remove labels.  Rubbing alcohol in a lint free cloth will remove residual adhesive.  My personal favorite technique is Krylon Adhesive Remover.

Mercury Glass Lamp 3

2.  Drill a hole where you want the cord to exit the lamp, in the back near the base.  For that technique, see my previous tutorial:  How to Make a Lamp From a Glass Bottle. Follow safety precautions!

3.  Clean away debris from drilling, dry bottle with a lint free cloth and tape over the hole you just drilled.  You will see why!

4. Pour Epson salt into bottle so that to about one inch from the bottom.  If your bottle is smaller, you can use less.  It is not important to be exact here.

5.  In a well ventilated area with protected work surface, spray looking glass paint into mouth of bottle.  Make sure to follow instructions on label.  You want to shake the can vigourously before using.  If your bottle mouth is small in diameter like this genie bottle, you will have paint pooling in one spot and running down the neck.  That is fine.

6.  Shake the bottle like a snow globe, so that the salt grabs the paint and drags it around.  This will create the mercury glass look.

7.  Repeat steps 5 and 6 a few more times, allowing each coat to dry for about 5 minutes before applying the next.  Stop when are happy with the look.

Mercury Glass Lamp 6

8.  Follow instructions on your lamp kit to assemble.  The one used here was super simple to and cost $6.

9.  Use a thrift store or new lampshade to fit your décor.

EXTRA TIPS

○ The salt will stick to the wall of the bottle in spots, giving a lovely crystal effect.  You can pour as little or as much of the salt out as you want after painting.

Use this technique for recycled glass bottle vases, votive holders, wind chimes and more.  Keep in mind this only works when the sprayed surface is inside.

Easy Avocado Egg Salad Recipe

Easy Avocade Egg Salad Recipe

 

Avocados not only taste great, but are one of the only fruits that contain heart-healthy monounsaturated fats.  They help lower bad cholesterol, elevate good cholesterol and can be used in place of butter in your favorite recipes to cut back on saturated fats. Today I am sharing a yummy, quick and easy recipe for avocado egg salad.  Serve up something a little different  at your next get together.  The potato salad won’t be missed!

INGREDIENTS:

(SERVES 8)

2 avocados

2 lemons

1 medium sized red onion

1/2 cup mayonnaise

1/2 cup toasted walnuts

10 hardboiled eggs, peeled

Salt and pepper to taste

Side dish recipes

DIRECTIONS:

Stir together in a large mixing bowl:  Juice from 2 lemons, 1/2 cup mayonnaise, 1 tbsp water.  Mash in with fork the yoke from 2 hard boiled eggs.  Add salt and pepper to taste.

Add 8 chopped hard boiled eggs , 2 chopped avocados and 1/2 cup red onions chopped.  Stir until well coated and serve over tomato slices.

Top with 1/2 cup toasted walnuts.

Enjoy!

DIY Wine Bottle Candles

How to make Wine Bottle Candles @savedbyloves

Scented with your favorite fragrance, these beeswax and soy candles are easy to make and great for all occasions!  We will be cutting wine bottles and using the bottom section as a container for pouring our candles.  Get started now and give these inexpensive, eco-friendly, handmade treasures as Christmas gifts that are sure to impress!

 MATERIALS

 

Wine Bottle Candles 1

Beeswax or Soy Wax

Scented Oil

Soy wicks on metal tabs

Double sided adhesive

Melting Pot and large sauce pan for boiling water

Cut wine bottles for candle containers (See How I Cut Wine Bottles)

Bamboo Skewer or pencil

Craft wire or rubberbands

Scissors

Lint free cloth

Soap and water or glass cleaner

 DIRECTIONS

 1.  Melt wax per instructions.  I used an aluminum melting pot placed in a large sauce pan of boiling water.  Add scent if you are going to do that.

Wine Bottle Candles 2

2.  While that is melting, prepare container and wick. Clean container well and dry with a lint free cloth.  Adhere wick tab to double sided adhesive, and stick other side into container.

Wine Bottle Candles 3

  1. Wrap excess wick around dowel rod, centered so that wicks are straight up and down.  Use wire or rubber band to attach a second dowel rod to the first, sandwiching the wick in place.

Wine Bottle Candles 4

4.  Pour in wax until container is as full as you would like.  Let sit overnight, trim wicks and enjoy!

Wine Bottle Candles 5

EXTRA TIPS

○ Use printable labels to customize your candles for gifts and holidays.  Etch monograms and patterns like I showed you in the Monogram Tumblers project!

For more inspiration, visit our 50+ Glass Bottle Crafts:

Cut Wine Bottle Bracelets

Create Bracelet From Wine Bottle Glass

Your friends will be amazed when you tell them these bracelets use to be wine bottles!  This project involves cutting glass and firing in a kiln, but you could do a version without the kiln too.  Use rub on transfers and alcohol inks to create a piece of wearable art!

MATERIALS

-glass bottle label removing and cleaning supplies (see techniques)

-glass bottle cutting supplies (see techniques)

-stainless steel measuring cup

-kiln

-kiln wash

-glass drilling supplies

-jewelry chain

-jump rings

-toggle clasp

-two pairs of jewelry pliers; flat and or needle nosed

-alcohol inks and felt pad applicator

-non stick craft sheet

-rub on transfers

-beads and charms for embellishing as desired

-permanent marker

 DIRECTIONS

 1.  Cut a ring from your chosen bottle (See How to Cut Wine Bottles)

Make jewelry from wine bottles

Wine Bottle Bracelets 3

2.  Carefully score ring with glass cutter and tap to break score, leaving you with a half circle.  Score this to the size you would like your bracelet to be, about 2.5 inches.

 Wine Bottle Bracelets 4

3.  Place bracelet piece on kiln washed stainless steel mold or measuring cup as shown and fire to full fuse (see techniques).

Wine Bottle Bracelets 5

4.  Once the bracelet is cool, remove it from the kiln.  Mark for placement of holes where chain will be attached with a jump ring.

Wine Bottle Bracelets 6

5.  Drill the holes using small diamond bits (see How to Drill Holes in Glass).  I use this diamond tipped micro engraving drill bit kit for my small holes.

Wine Bottle Bracelets 7

6.  Begin drilling at the mark, coming in at an angle to start your hole, then moving to 90 degrees as described in the techiques.  Make sure to cool the drill bit in water every 30 seconds or so to prevent glass from shattering due to heat.

Wine Bottle Bracelets 10

7.  Apply rub on transfer per instructions to the front surface of the bracelet.

Wine Bottle Bracelets 12

8.  Use felt applicator or brush to apply alcohol inks to back surface of bracelet.

 Wine Bottle Bracelets 14

9.  Open jump ring using two sets of pliers to twist each end in opposite directions.  Do not pull ends apart to open, rather twist open as shown.

10.  Attach the appropriate length of chain to get desired bracelet length and close jump ring by twisting ends back together.  Keep in mind the closure will add about ½ inch to the length of the bracelet.

Wine Bottle Bracelets 15

11.  To finish, attach toggle clasp ring to one end and bar to the other, using a jump ring for each.

 Bracelet on Fire

EXTRA TIPS

○ Create custom bracelets, earrings and pendants using this technique.  Use blank rub on transfer paper made for inkjets to transfer your own designs to your recycled glass jewelry!

DIY Cut Wine Bottle Table Number Centerpiece

Cut wine bottle wedding centerpiece table numbers tutorial @savedbyloves

With just a few simple supplies, you can make this charming wedding reception table number centerpiece for that special day.  Not only that, this can be used for an eco-friendly centerpiece for any occasion!

MATERIALS

DIY Wedding

-Three Green Wine Bottles with corks
-Burlap ribbon
-Lace
-flower embellishments (die cut, hand cut or buy in the scrapbook section of your local craft store)
-18 gauge craft wire
-Antique finish metal chain
-Blingy metallic and other ribbons
-Wedding themed paper craft embellishments
-Adhesive crystal sheets
-Chalkboard tags
-Decorative brad
-Monogram sticker
-Photograph of couple
-Quick grab craft glue or hot glue
-Wire cutter

TUTORIAL

1. Cut your wine bottles to 3 different heights (See How to Cut Wine Bottles)
2. Smooth out any pointy edges with grinder or sand paper.
3. Clean the bottle with alcohol or glass cleaner. I like to wear gloves after cleaning the bottle to avoid fingerprints.
How to cut wine bottles

4. Tie burlap ribbon and lace around two of the bottles near the base.
5. Wrap sparkly twine or ribbon around neck of the remaining bottle and dangle a chalkboard tag with the couple’s monogram from it. Place a decorative brad at the top of the tag.
6. Embellish bottles by gluing on flowers, placing adhesive crystals and draping metal chain as shown.
Wedding Table Number Bottles5

7. Make the wire place card/photo holder. I picked up a picture display at a garage sale and cut the wire holders from that. You can easily make your own with 16-18 gauge wire. Cut a piece of wire about 5 inches and wrap one end around a cylinder shaped object a few times (Highlighter markers or small prescription bottles work well for this.). Bend wire at the base of the circle you just made. You can use round nose pliers to make the little loop on the circle part or just leave as is.
DIY Wedding Centerpiece

8. Insert wire into cork. Create a pilot hole in the cork with a needle tool, small nail or straight pin. Insert wire holder into pilot hole and add a dab of hot glue to secure.
Wedding Table Number Bottles7
9. Place table number, sentiments and photos as shown.

EXTRA TIPS

○ Use this concept for holiday centerpieces, photo displays, anniversaries and other occasions by changing embellishments to match the theme.

Washi Tape Wine Cork Keychain DIY

Corky Washi Keychain

Carry your keys in eco-friendly style with this washi covered wine cork keychain.  This project is simple and quick, and makes a great handmade last minute gift or party favor.  Decorate with ribbon, paint, stickers and stamps as a variation!

MATERIALS

Corky Washi Keychain 1

 

-Cork

-Eye screw

-washi tape

-scissors

-keychain findings

-jump ring

-2 pairs of jewelry pliers

DIRECTIONS

1.  Cover cork with strips of washi tape as desired.

Washi tape craft

2.  Place eye screw in center on one end of the cork.

Corky Washi Keychain 3

3.  Use both pairs of pliers to twist open jump ring as shown.

Corky Washi Keychain 4

4.  attach key ring finding to eye screw with jump ring then close jump ring, using both pairs of pliers to twist it back to the closed position.

Corky Washi Keychain 5

Corky Washi Keychain 6

That is it!

For more inspiration, visit our 50+ WINE CORK CRAFTS:

And our 50+ Washi Tape Crafts

DIY Washi Tape Wine Cork Keychain @savedbyloves

DIY Wine Cork Bulletin Board

How to Upcycle Wine Corks into Home Decor

Stay organized, eco-chic style with this cork board made from… corks!  This project is simple, functional, stylish and can be super inexpensive with a thrifted frame.  Start saving those wine corks, ask your friends to save them, and hit your local recycle center to see if they can hook you up with some.  You are going to need quite a few, especially if you have a large frame.

SUPPLIES

Framed Cork Bulletin Board

-Wine Corks

-Utility Knife

-Hot glue gun and sticks

-Frame without glass 

TUTORIAL

1.  Remove glass from frame, leaving just the backing.

Framed Cork Bulletin Board2

2.  Decide on a pattern for your corks.  Simple and repeating looks best.

Framed Cork Bulletin Board3

Framed Cork Bulletin Board4

3.  Starting in the center, begin gluing corks in your chosen pattern directly onto the frame backing.

4.  When you come to the edges where full corks no longer fit, cut the corks where necessary to create the appropriate shape to fit the space.  Continue until the entire frame is full.

Framed Cork Bulletin Board5

EXTRA TIPS

Seal corks after they are all placed for a glossy finish if desired!  These would be great for displaying bride and groom photos for your wine themed wedding reception.

For more inspiration, visit our 50+ WINE CORK CRAFTS:

Easy Fried Green Tomato Recipe

Easy Fried Green Tomatoes

 This year my tomatoes are taking their own sweet time ripening to the red that we all know and love.  That, combined with the fried food theme at last week’s Bible study pitch in, prompted me to make fried green tomatoes for the first time ever.  I would make them everyday if eating fried food didn’t creep me out so much.  They were simply delicious.

How to make Fried Green Tomatoes

I bought a cheapo deep fryer a couple of years ago to Mr. SBLC his beloved chicken wings (See Amazing Hot Wings Recipe).

Here is the recipe I used (from My Recipes):  Fried Green Tomatoes

I followed it exactly except I dropped mine in the deep fryer for 2 minutes instead of frying on the stove.

They are sooooo yummy, I am hooked.  We have tons more green tomatoes out there, just waiting to be battered and fried!

Kitchen Cabinet Makeover With Chalk Paint® decorative paint by Annie Sloan

How to Paint Wood Cabinets

So my sweet friend Krystal wanted to update her oak kitchen cabinets in a big way.  For like 10 years she wanted to update them.  A decade of cabinet dissatisfaction is enough. That is why I was super excited when the chance to use  Chalk Paint® decorative paint by Annie Sloan came my way.   Today I am sharing how we seized the opportunity, using the Chalk Paint® in colors Old White and Graphite, in addition to the Clear Soft Wax to create the look she was after!

Annie Sloan Chalk Paint

Annie Sloan Unfolded sent us the paints and wax.  This paint is simply amazing.  More about that later.  For brushes, what to use depends on the look you are trying to achieve.  We wanted texture and messiness, and we knew we would be distressing with sandpaper after painting, so we went with the cheap chip brushes you can find in the dollar bin at your local craft store.  There is a wide variety of techniques to use and looks to achieve with these products.  A fantastic place to start is with Annie Sloan’s numerous books on the use of paint in decorating.

Kitchen Before Paint

Here you can see the oak cabinets before we got at them.

Not so great, right?  

We decided to go multicolor, Old white on top, Graphite on the bottom.

How to distress cabinets

 Kitchen Makeover

We just removed the doors and started painting them and the frames.

NO PRIMING, NO SANDING.

This paint is amazing.  It looks wonderful and takes no prep.  Um, yes please.

Distress Technique

It dried super fast.  We did 2 light layers, letting dry about 20 minutes between.  For a distressed look, we lightly sanded the edges and corners randomly on the cabinet doors.  A little bit of distressing goes a long way!

After distressing, we applied the wax with a polyurethane brush.  Super easy!

The coverage  of this paint is unbelievable, really.  I use a lot of different paints in my projects, and this is tops.  Granted it is more expensive than other options, but the difference in quality is significant.

Annie Sloan Paint Project

This entire project was about 24 hours in duration!

Kitchen Cabinet Makeover

What a huge difference!  Remember the yellow above the cabinets…

Kitchen Cabinet Redo

We painted it Old White and added crown molding.  For more on how to install crown molding, see my first experience here!

I think the biggest surprise for all of us involved in the project is the countertops.  That’s right.  We were making plans to do a countertop transformation after painting the cabinets.  We were just certain the new cabinets were going to make that totally urgent.  We found the opposite!  Somehow, the pinkish/mauve looks adorable with the Graphite and Old White!  Did not see that coming at all.

Kitchen Cabinet Upgrade with Chalk Paint

If you want to transform your from outdated to rich and beautiful, this is a great option!

Find everything you need to get going here:

Privacy Policy